Hi guys new to this forum David from Glasgow - i own a 2014 (64) 520d the headlight washers have not been working since last winter. The stalks are free moving when i manually use my hands to bring them out. so they are not stuck. are these fed off the main pump or is there seperate...

This morning for no apparent reason my front windscreen washer stopped working. No pump sound at all. (Touring - and the rear is fine) The wipers are not always giving their usual sweeps when the stalk is pulled - they do at the first few tries Where do I start?

Genuine or any old crush washer of the correct dimensions? Can get genuine ones off ebay for like £5 each, which is silly, or ten 14 x 20 x 2 crush washers for about the same.

The screen washers stopped working this week but the rear still works, so assumed it was the pump. Took the inner arch liner out and removed the screen pump out but decided to test the voltage on the connector and found there was no volts when the washer/wiper stalk was pulled up. I was also...

Looking for a SPORT Front Bumper ( Topaz) for our 2003 325Ti Sport Compact which also has Headlight Washers as the bottom is Cracked. 07799145076

Hi, has anyone ever replaced the three windscreen washer assemblies on 530 GT? Cant seem to find any info on forums!!

Hi guys! I've just put my F30 from into a garage for a MOT and unfortunately it has failed because of not working headlight washers. My local BMW garage called me to let me know that some parts may need to be exchanged in order to fix it, which is fine as I still have BMW warranty. However...

Hi all, On my 635 d on occasions I pull the wiper stalk back to wash the screen and no water comes out but the wipers sweep. There is no pump noise when this happens. If I pull over and switch the car off and on again they work as normal. Anyone got any ideas? Thanks Jim

Might sound like a dumb question but how do I tell if I have headlight washers, I have the 2 square panels on top of the front bumpers but they have never functioned, do all bumpers have the blanking plates on them or is it they are there but not working

as title..i had the car to bits other day..ie pollen housing/tray/windscreen wipers strut bars etc.i was replacing spomething that id forgot to replace,,anyway the washers were not working today..took pollen cover off,i could see it was wet inside and pump was working,,maybe a pipe had come...

Hi all. I find the headlights on my E46 coupe very poor and want to upgrade with ONB or PXV +130s. I'm 90%sure they're projector lenses (they look like a eye lens) but want to make sure first. Thanks, Jimbo

Anyone know of a way to override the control logic and force the washers on for test purposes?

Today ive found that my washers only dribble out but if I flick the wiper leaver many times the water pushes out further enabling me to clean the window but holding open the leaver only allows a dribble? Any help appreciated Thanks

Are the headlight washers suppose to work when the lights are on auto? Mine work when I switch the headlighs to the far right but if they are on auto they dont?:confused

Hi Guys, Im new to the forum so please excuse me if i have posted this in the wrong section as im just getting to grips with the site. I have a 58 reg 318 Saloon and my window washers stopped working completely but motor still makes noise, the bottle was full so tried the motor again maybe too...

OK the washers have been poor for weeks after using hot water to try and clean them out they are now down to a dribble/no water. If its the pump I have to clean where is the washer bottle to the front or rear of the offside front wheel. thanks

Hi, is there a way to manually operate the headlamp wash on an E60 Msport? It appears that only one side is spraying.

This procedure disables the headlamp washers by unplugging the relevant washer pump. It does not affect the windscreen washers, and does not cause an error on the console. Carried out on a RHD vehicle. The tank is in the front wing on the same side as the washer fluid filler neck. Notes: -...

Gents Going to replace my wishbones and mountings/bushes this weekend on my E46 318i registered 2000. When I look at TIS it informs me that if 66mm mountings are used a special washer S in the picture attached is required to stop the cruciform from rubbing the mounting. Is this washer...

The motor is working but no water comes out. How do I get to the motor to check for blockages?