sensor

So my wife's E90 318i has started to judder alot when driving, especially when it's in low gears with little acceleration. If you carry on driving it, it also goes into limp mode. The traction light is constantly flashing and sometimes it'll throw up the ABS light and red handbrake light...

I’ve got an electrical issue that I’m coming to my wits end. Happened last year and still not got it resolved. E36 3.0 M3. Track prepared but still road legal. Problem is this When sidelights and headlights are off the indicators work fine but the nearside (UK) sidelight flashes with the left...

Help Oil level sensor has melted the earth wire on top of the engin On the harness to the oil level sensor with the ignition on engin not running as doesn't start now Pin 1 has 3.66v Pin 2 is earth Pin 3 has 12v Is this correct Do i have faulty sensor causing the fire or is it the modual...

Hi, I have a 59 plate 3 series that I'm having nothing but problems with! I thought it was sorted when I spent £400 on it last month for abs sensors, various plugs and coils. I've not had a pick of bother with it since..... until yesterday. I was driving along, only around 25mph when the red...

Does anyone know what this sensor does and part number Been to bmw

Hi There, Can anyone tell me what this sensor is for? It is located in the driver's side front splash guard. See photo. Thanks Austin

I had an engine warning light on my e46 had it code read it said bank 1 and bank 2 to lean so had both lambda sensors changed £250 fitted still getting engine warning light bank 1 and bank 2 lean and on tick over at lights and parking up the revs going up and down i know they were fitted my pal...

Hi all so I check my codes after I get the start stop error appear . I get the code brake vacuum sensor , signal 2FD3. Seems this is quite common . Is it a diy repair or shop job ? How do I go about it ? Cheers

I’ll be driving my 2001 325i and all of the sudden it feels like the drivers side front wheel grabs for a second and then lets go. Then the yellow dash DSC and “Brake” light will come on and stay on until I shut the car off. They usually reset. Occasionally, when driving, the yellow DSC light...

Hi, I hope somebody can help, car is a 2003 E46 330i. I have had to replace the starter motor. (nightmare!) during the removal of the inlet manifold I managed to accidentally pull the wires out of the coolant temperature sensor connector. I've managed to salvage the connector and remove both...

where is location of low pressure sensor on bmw645 engine anyone ?

Hi folks :) This fault came up today, with a warning next to it saying "Pending Fault" Does that mean that the sensor hasn't actually gone, but i about to? I cleared it, and it hasn't come back yet after another 5 or 10 miles of driving..

I have a 2006 diesel E91 320d which suddenly started running rough, then wouldn't start. It has a fault code 3EC1 showing. I have seen videos of the camshaft sensor being removed on the petrol engines but can't find the sensor on my diesel engine. Does anyone know where it is located?

hi, and thank for your letting me in to your forum. this is my first post here so please excuse my english and bad set up :) okay, so i have an 2001 BMW e53 X5 3.0L 6cyl automatic. whit 312000KM on it. it has been running great now and still does but engine management light comes on every now...

Hi, having a problem with my e36 323 (late 98 model) Basically it needs a crank sensor, cant get a direct replacement from anywhere. So i started looking in to why i couldn't get 1. I found that apparently BMW did a loom and sensor conversion back in the day. Does anyone thow about this? TIA Rob.

Hi, Hope someone can help. I have to replace my eccentric shaft sensor and I'm looking at some used ones on eBay. There appear to be two different types though both are allegedly suitable for the N46 engine. The obvious differences between the two are that on the back one has a small square...

Hell guys, I am facing horrible issue I measured my o2 sensors (car has only 2pcs) with ELM 327 scanner and pre cat o2 sensor was showing 0 volts no movement at all. So I thought it is faulty I replaced it with new one but ELM still shows 0 volts, I do not know what to do I think I will ring...

Hi could you please give me a quote for the 2 rear corner pdc sensors for Yf56lkl also would these come pre colour coded. Many thanks again

HI Guys, Can the throttle position sensor be changed on the throttle body of my 728i rather than buying a new expensive £625.00 throttle body. I look forward to your replies, thanking you in advance. Lee

Guys, Has anyone had trouble with a p0365 fault code before? I've had it on for a while. Replace the CPS exhaust side for a new OE part. Fault code still on. Any ideas what to do next?