BMW Forums : BimmerForums banner

resistance

  1. Hepl 640d 2012 f13 error 930958 drivers active head restraint resistance too high

    Auto Electrical Forum
    Hi im after some help with error code 930958 on a bmw f13 640d coupe 2012. Does any one have the drawings for the seat loom and also any other information that might help me. I have changed the head restraints over and the faults stays with the drivers seat. I can reset the error but it comes...
  2. E60 Airbag Problem. 9AF4 drivers seat belt tensioner firing circuit resistance too high

    Auto Electrical Forum
    I had my airbag light come on several weeks ago but had it turned off with SNAP ON Diagnostics but it had the error 9AF4 drivers seat belt tensioner firing circuit resistance too high, is this the seat belt occupancy problem that you can bypass? This is my first E60 so I am in the middle of...
  3. 2005 E83 2.0d - airbag warning light, passenger side, resistance too high

    BMW X Series - Tech Talk For All Gen Of X Series
    Hi all, The mrs. E83 has the airbag warning light on. I've read the codes and the relevant ones seem to be: zk0 - driver airbag stage 1, resistance too high (not currently present) zk3 - passenger airbag stage 1, resistance too high (currently present) zk11 - passenger airbag stage 2...
  4. Cps resistance

    BMW 3 Series Forum - Technical Talk on the BMW E21
    I have an m50b25nv, and the car when hot sometimes will refuse to start, stumbles then dies. I have tested the crankshaft sensor, and got 596ohms? Would this cause the hard starting and slight misfire? Thanks
  5. E90 Front & Rear Level Sensors - Resistance

    Auto Electrical Forum
    Hi all, does anyone know what max/min resistance the front & rear sensors are on an E90 ? (LWR axle sensors) Thanks in advance Graham
  6. What should the resistance be on Glow plugs for a 320cd?

    BMW 3 Series Forum - Technical Talk on the BMW E46
    Just checking the glow plugs for resistance as I don't have a 5v power supply to check them by seeing if they heat up. I have them out of the engine and am checking by resistance but can anyone tell me what their resistance spec is so I can compare my multimeter reading to it. Cheers! The car...
  7. BMW 316Ti SE Compact 2003 - Seat Belt Tensioner Resistance Too Low Problem

    BMW 3 Series Forum - Technical Talk on the BMW E46
    After buying this car cheap as it had a few problems I fixed them all, but this Error Code 02 Drivers Seat Belt Tensioner Resistance Too Low would not clear. I bought a used tensioner which didn't make any difference. Cleaned all plugs and connections on the cables to no avail. So today sunday...
  8. Ignition coil resistance testing- BMW E36 1993 2.5i

    BMW 3 Series Forum - Technical Talk on the BMW E21
    Hi I want to test the ignition coils for resistance. Does anyone know what the recommended resistance level is? I've read online that anything between 0.4 to 0.8 ohms between the two outer terminals in the coil plug housing is good?
  9. E34 540i Supercharged, MAF Wire resistance issue, help please!

    Supercharging your BMW
    I have installed an ESS kit on my E34 540i. It's making good power but is leaning out at the very top (around 6k+) As you guys know, included in the kit is a circa 2000ohm resistor for the maf wire. It is throwing a code for the hot film air sensor. I have spoken to Hans at ESS and he said...
  10. 1993 525i E34 Ignition Coil Resistance

    BMW 5 Series Forum - Technical Talk on the BMW E12
    Does anybody tried or have measured the secondary resistance of the ignition coil BMW 1 703 359?
  11. Spark Plug Wire Resistance

    BMW 3 Series Forum - Technical Talk on the BMW E21
    Hi,Anyone know the spark plug wire resistance for e30 m3?
  12. Query on coil resistance seen many different values for same car

    General BMW Discussions
    Hi everyone Tested coil and get 6500 ohms on centre and only 27 across terminals(did off car)(according to findings should be .5 - .85,not .27.Centre reading ok) This is the prob at the mo,a few people have said the manual specs are wrong.I can't get to a shop to test as 7.5 miles away and...
  13. 1998 E36 325se fuel sender fault ,, resistance (FIXED)

    Auto Electrical Forum
    hi ,, just checked the resistance on both senders left one about 15 ohms right one not even registered on meter , i think the right one is at fault , can anyone confirm this ,, just to refesh you on fault , fuel gauge on empty no fuel low warning light on , binical test gauge ok :confused 98...
  14. 1991 535i E34 Ignition Coil Resistance Readings

    BMW 5 Series Forum - Technical Talk on the BMW E12
    I have got a primary resistance reading of 1.0 and the secondary resistance is within range,the manual specs says it should be around 0.5,is this a coil that could be open and in need of replacing?
  15. 1991 E34 535 M30 - HT Leads Resistance Check,Are These Good Or Bad?

    Auto Electrical Forum
    E34 535i M30 HT leads have been tested today with a multi meter set at 20k and these are the following readings,the reading which concerned me most was from the the King Coil Lead. King Coil Lead: 1.99 HT Lead: 1=6.03 2=5.58 3=5.90 4=5.56 5=5.95 6=6.06 This car is a non starter and I am not...
  16. 1993 E36 325i resistance when changing into 4th gear

    BMW 3 Series Forum - Technical Talk on the BMW E21
    hi i have a problem when changing into 4th gear either up or down, i get like a not so much as a crunching noise but some resistance.. this only happens when giving it some shoe or have been, but only going into 4th? any help or sugestions would be apprieciated:confused:confused
Top