point

I’m looking to swap over control arms / wishbones, the job itself is no problem, but was wondering what jack and axle stand points would you use? I normally jack the car up using the black rubber point by the driver and passenger doors and would then throw an axle stand under the control arm to...

hi has anyone ever came across a failing mount point? One of the The plastic blocks started to push into the sill underneath. Is this something fixable or is this the end of the car's life? i doubt it would pass MOT in 3 months like this.

Yes there is. https://www.newtis.info/tisv2/a/en/g30-530d-lim/repair-manuals/00-maintenance-general-note/00-02-raise-vehicle-tow-away/1VnYcMLZy0

Is there a front jacking point under the engine in the current G30 5 series

Hi I am trying to recharge my air con on my BMW F32. Can someone tell me where the F32 low pressure air con recharge point is located? I have found what I think is the high pressure connection to the right of the engine bay with a black cap on. My air con gas recharge connector will not fit...

Hi, hoping someone can help! I'm frequently getting new fault codes appearing as the car is going into limp mode in 3rd gear under load (high revs / uphill in particular). I was wondering if anyone could point me in the right direction for: 1) A diagnostic code reader I can purchase which is...

2006 E90 325d M-Sport Saloon - ISOFIX Top Tether Point Hello, first time poster. Just picked up the above car and looking to install a forward facing ISOFIX seat however I just can't find a top tether/anchor point anywhere. The car does not have the folding rear seats. I can find the...

Hi, I have a BMW E90 330D 2007. I've read lots about modifying the clutch by a clutch stop to shorten the travel, and removing the CDV to get more reliable clutch engagement which i will do. However, the biting point if quite far down the pedal (near the floor), after the clutch has engaged...

....

Hi All just failed mot on corroded osr jacking point other 3 are perfectly ok,most of its covered by plastic covers so when these as removed think it might be quite bad. This is on a vehicle which has had an easy life owned by us since it was a year old no accidents always...

... ....

The main advantage of a vertical line array system is described above. When correctly installed, a line array allows even frequency response and clear sonic coverage throughout the range of the system (except for the nearest and farthest seats). And unlike traditional point source speakers, you...

Hi all, First post on the forum and just trying to get my bearings with a problems ive come across , so I got a E36 318ti last week and in essence I've come to jack the front up to find where the jacking point is it's had a previous repair but looking at it its just a plate weld over the top so...

Hi, I'm about to purchase the above vehicle. The jacking points have completely rusted out. Can anyone advise where to get replacement panels for the job and if there is a how-to anywhere on the forums about replacing them? Thanks in advance, Richard.

Hi All, Might seem a silly question but I've checked several youtube videos and even asked a garage and I can see where the jacking points are, behind the front wheels, but obviously I can't jack up the car and put axle stands on the same point, (it's too small, and they say not to jack...

Hi, Recently bought a 55 plate 116i. Seems to be running OK apart from it judders in 5th when going over a bump and low revs. Apart from that when I change low gears the clutch and throttle will occasionally stick at the biting point. As I lift the clutch and lower the throttle it's like...

Hi All, I was wondering if I could get some help from all the E36 owners out there. I am trying to buy some car mats, but I do not have any confidence that the mats from online websites will have the hole for the fixing point in the right place. Please see link below for one website that urges...

Hi Trying to fit a dashcam to my X5 E53. Ive hooked up the wires to fuses but cannot find a decent fuse point anywhere round glove box. If anyone could advise that would be greatly appreciated. Thanks, Dave

Hi I have a hole on the floor of the side skirt where the plastic jacking point should be under the car. Is it as simple as cutting then welding a new section in and if so how do I reattach the plastic foot to the new metal ?

Hi everyone, Maybe a daft question as the car has very obvious jacking points! I'm going to change the oil and filter on my 528i. I have one trolley jack and not much room to be able to get my axle stands under the car. My Honda Accord had a central point to jack which meant both wheels went...